Plastic bottle feeder for birds: 700 photos, instructions

 

In the article you will learn how to make a bird feeder out of plastic bottles different sizes, from small 0.5 liters to 2 liters, both from a separate bottle, and in different combinations. So prepare empty bottles and call the children, it will be interesting.

How to make a bird feeder out of a plastic bottle

Bird feeders are a great way to bring birds into your garden. You can buy fashionable hand or industrial products, but it’s much better to quickly and easily make a feeder out of items that you throw away anyway. Here is a good example, how to make a feeding trough from a regular plastic bottle and a pair of wooden spoons. You just need to make holes in the bottle for the spoon and set it so that the feed enters the inner surface of the blade.

Nice idea and a great project for children.

Find a suitable bottle of 1.5 or 1 liter. Wash to remove traces of the original drink and allow to dry. You will also need two wooden spoons or similar wooden objects (dowels, spatulas, etc.). They can be old, used or new from the store.

Determine where you will cut holes:

• Measure the first hole from the base of the bottle approximately 10 cm up. Draw an asterisk approximately 10 mm in size. Then rotate the bottle 90 degrees.
• Measure the second hole 5 cm from the base. Mark this place with another asterisk.
• Draw a 2.5 cm circle next to the star on each side of the bottle.

Make cuts. Use a knife, it's better than scissors, and easier to handle when cutting the bottle.

Pass the wooden handle of the spoon through a hole on one side and then through an asterisk cut on the other side. Repeat in the opposite direction for another wooden spoon. Both spoons should fit tightly in the bottle. They form both poles for birds and feeders for seeds.

Screw a small hook into the bottle cap. Pass the thread or twine and firmly fasten. If there is no hook, you can simply wrap around the neck.

Fill the bottle with bird food. Wrap the cap.

Hang in a suitable place in the garden.

Make sure that the feeder is balanced and that the feed enters the spoon blade.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Here is a similar option, too plastic bottle feederwith just one wooden spoon. You can do so, well, if you suddenly have only one wooden spoon, do not give up the idea. The materials are basically the same: a 1.5 liter plastic bottle, screw or hook, cord, wooden spoon, knife or scissors.

The manufacturing procedure is described above, and if over time more spoons appear, then you can always remake your feeder and even insert three or four pieces.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

See how to do the same bird feeder from a two-liter plastic bottle, in this case, from Coca-Cola. What is not very beneficial for our stomach is great for feeding birds. Using a plastic bottle to make bird feeders is so simple that I recommend you do it from every bottle that gets into your home. For work you will need a clean plastic bottle, wooden sticks for use as perches, a knife, a strong rope, wire or twine. Another marker, a funnel is also useful, but not necessary.

Well, then do as in step-by-step photos. Note, make holes, insert poles, insert wire or cord. Then find the perfect place, sprinkle the feed and lead the feeder.

• 
• 
• 
• 
• 
• 
• 
• 
•  

 

Or so, basically the same thing, only add some scotch tape. Cut holes in the bottle opposite each other. Just insert a spoon into the holes. Please note that the side where the feed will be served is the large side of the spoon. Tape one side with tape as shown in the photo. Everything yours plastic bottle feeder ready.

• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make a bird feeder for a child

Need to cook:

• Plastic bottle
• Plastic cups from yogurt
• Wire or cord
• Bird food

Do not leave children alone, make sure that they observe safety measures.

Walkthrough

Cut a hole in the side large enough to allow for free feed, but just don't wake up on the ground with the slightest gust of wind. Make some small holes in the bottom of the bottle so that rainwater can drain.

Hang the feeder on a tree. If you are doing a few pieces, then you can pull the wire and fix several feeders on it. But they must be monitored, if the feed begins to mold or the bottle wears out, just make a new feeder, with the experience gained it will take several minutes.

Tell the children that the birds are counting on them and will starve in winter if you forget about them.

We make a bird feeder with children

We wake up with birds singing from spring to autumn ... sometimes in winter, but not so often. Tell the children from a very young age what benefits these little creatures bring to people, how to protect them and take care of them. Making bird feeders from a plastic bottle, a very simple process, so you can even attract preschool children, of course, together with adults.

Prepare the kids for fun. You can instruct them to collect small twigs or what you intend to use for perches.

Prepare the bottles and wash them well. When cutting plastic better work with a hot knife. Find a knife that you no longer need because using it will most likely have to be thrown away. Make holes for the feed and stand.

Assign the children a simple job so that they develop their small motor skills. For example, align the bottle, attach and stick poles and various decorative elements. And of course, let them participate in the installation of the feeder. They feed you with food, hang it on a tree or other suitable place.

Do something special with your children today.

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bird feeder with baby hands from a bottle

We all know that plastic causes enormous damage to the environment, so its reuse is a useful and necessary thing. The less plastic waste gets into landfills or into our bodies of water, the greater the benefits to nature. You can take it one step further and engage the children in the creative process to enable them to save the world.

By showing children how to do various useful things, we help them discover their creative potential so that children can fantasize and come up with their own projects.

How to make a feeder from a plastic bottle of 1.5 liters

This is a simple project, but it requires working with sharp objects, so it is best to do the dangerous work for adults, and then let the children decorate it.

Materials

• 1.5 liter plastic bottle with cap
• Boxes
• Scissors
• Sharp knife
• Rope or wire
• Paints
• Nail polish if needed

Method

• Cut off the top third of the bottle.
• Cut the line from the cut bottom of the bottle about two-thirds down, then across and up to form a rectangular shape.
• Pass one end of the rope through one of the holes in the bottom of the bottle, remove and secure from the inside.
• Pass the thread through the hole in the top of the bottle, from the outside, to the inside.
• The top of the bottle should fit snugly against the bottom with a beautiful small rectangular hole for the birds.
• Pull the remaining rope through the hole in the cap to hang the bottle.

Have the children paint the bottle in the colors of their choice. Remember that the paint must be weather resistant. Do not stick decorations or stickers so that birds do not peck them. Once the paint has dried, hang it on a branch, fill it with seeds and watch the birds flock to a treat.

Bird feeder from a small plastic bottle

In fact, everything from shampoo and mouthwash bottles can be used to make various useful things. Tell the children about this, they will probably give you a lot of interesting ideas. Presented here project of bird feeders from a plastic bottle Great for working with children.

First you need to make sure that the bottle is completely cleaned inside and dried. Also, find the plastic cap wider than the bottle with a small comb. You will also need several cable ties, twine, a sharp knife and scissors. And an adult. Because many of these steps are not intended for the child. Nevertheless, your baby can do simple bonding, garter and, of course, fill the plastic bottle with food.

I think the idea of ​​the design is understandable, to make holes and attach the bottle to a wide lid or plastic container with low sides. Pull the cable tie through the holes in the bottom of the cap and bottle. Then tie two long pieces of twine around the cable tie, leaving the top untied to tie to the tree. That's all, fill with seeds, put on the lid and tie it to the branch.

• 
• 
• 
• 
• 
• 
• 
• 
•  

Easy bird feeder

• To create this slightly fancy design you will need:
• Plastic bottle 0.5 liter.
• Plastic bottle 1.5-2 liters.
• Plastic bottle 5 liters.
• Glue gun
• Bamboo sticks or pencils - 4 points.

Assembly order.

1. For 2L and 5L bottles, cut the bottom
2. Make holes for the feed.
3. Glue the bottom of a 0.5 liter bottle into a 2 liter bottle.
4. Glue the “nipple” to the 5 L bottle, thread the rope and tie a knot from the bottom.
5. Insert sticks
6. Everything is ready. Pour the feed and tighten the lid.

Design (optional)

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Plastic bottle and food container feeder

This is a bird feeder, mainly made from a plastic bottle and a cheap plastic food container, easy to manufacture and will not cost you anything. But, according to the author, she withstood a very harsh winter and many attacks of squirrels.

What you need

• Plastic bottle
• Plastic food container
• Glue
• Sharp scissors or knife
• Wire or cord

First cut some square holes in the top of the bottle. Then make a hole in the center of the cover. (this is for hanging). Several drainage holes in the bottom of the container.
Glue the cap from the plastic bottle in the center of the container, and the lid of the plastic container to the bottom of the plastic bottle,
Take the wire, make a hook and drag through two holes in the container lid and at the bottom of the bottle. Then fill the feeder with seeds and hang it on a tree.

• 
• 
• 
• 
• 
• 
• 
• 
•  

Small bird feeder

Many small birds like to peck food from the feeders, but sometimes they cannot get access, as the place is occupied by larger birds, especially pigeons. The design of this feeder is designed so that large birds cannot reach feed, and representatives of smaller species will feel comfortable without fear of competitors. To make such a specialized dining room - small bird feeder, you will need a 1.5 liter plastic bottle, a small plastic container, a 12 mm mixing bowl, a small 30 cm mesh cover and garden wire.

Necessary tools: wire cutters, scissors, hand drill, pliers, drills with a diameter of 38 and 16 mm.

The idea is to make a sphere out of a wire basket and a plastic bowl, in the center of which to fix a plastic bottle, with automatic feed. So the feeder will be protected from rain, and large birds will not be able to get inside the sphere. How to do this, look at the step-by-step photos, detailed instructions with all the nuances of the assemblies are on the site, you will find the link under the gallery.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

2 liter plastic bottle feeder for birds

This type bird feeders can be made from 2 liter plastic bottle or food container. In principle, you can use any bottle with a 2.5 cm cap. Just keep in mind that the squirrels will gnaw the bottle to get to the feed.

Step 1: Drill a 2.5 cm hole in the cover

Step 2: Using a small soldering iron, melt about eight holes with a diameter of 1 cm at the top of the bottle. These openings are designed to feed the bottle. Melted holes are better than drilled holes.

Step 3: Thread the wire. Melt a very small hole in the bottom of the bottle and run a wire through it. Bend a small loop.

Step 4: Fasten the cap. The lid will attach the food container to the bottle. Remove the cap to fill the container with seeds through the funnel.

Step 5: The feeder is ready, you can hang it.

• 
• 
• 
• 
• 
•  

Bird feeder made of wire and 2 liter bottles

Here's a simple way to reuse a 2 liter bottle to set up a buffet for our feathered friends. The idea of ​​a bird feeder consists in bending the “basket” from the wire, which will hold the bottle with the feed.

Materials

• 2 liter plastic bottle
• Galvanized steel wire.
• Thin galvanized wire (0.58 mm)
• Styrofoam Cutter
• Spray paint can

Tools

• Needle pliers
• Lineman Pliers (Power Combination Pliers)
• Portable MAPP Torch

Operating procedure

Step 1: Wire bend

2 liter bottle in this bird feeder held in a wire cage, which consists of a loop under the bottle and two rings around the bottle.

For this project, you will need to bend the wire into the following forms:

• A. Two rings that correspond to the circumference of a 2 liter bottle.
• B. One U-shaped loop passing under the bottle for support.
• C. Two bottom stops

Step 2: Bending ring

1. Fill the bottle with water and carefully put on the cap.
2. Wrap the wire around a 2 liter bottle 3 or 4 times.
3. Bend the rings by cutting the wrapped wire so that it is about a centimeter of overlap.
4. You need two of these rings - one will be located near the top of the bottle and one near the bottom.

Step 3: U-shaped support loop

Take a 1 meter long wire and center it on the bottom of a 2 liter bottle. Then bend the wire up on the sides parallel to the bottle. It is better to have an additional wire, if necessary, the length can be cut.

Step 4: Assembly and installation

Bend everything together. Most importantly, the rings fit snugly on the bottle. Ultimately, the rings will also be supported by a support contour.

Step 5: Bends

The poles consist of 15 cm long wire attached to the bottom ring. This connection is made by bending a small hook at the end of the wire and crimping it along the ring wire. They are mounted on the lower ring located between the support loop, so that the vertical wires (support loop and poles) are evenly spaced around the lower ring.
The poles must have a 90 degree bend so that they extend parallel to the bottle and then protrude to form a perio for the birds.

Step 6: Wire fastener

The easiest way to put everything together for soldering is use thin steel wireto link all intersections together.
To check, place a 2 liter bottle in the cage and make sure the rings are parallel and the support loop is upright

Step 7: Soldering

The most important thing, observe safety measures. Work on a non-flammable surface in a well-ventilated area. Do not try to do what you do not know. Seek professional help if you are not qualified. The author used a flux-coated welding wire.

Step 8: Hanging loops and hook

Bend the upper ends of the U-contour into rings with a diameter of 1.5 cm. Turn the upper part inward, starting at about 30 cm from the bottom of the bottle, to make hooks at both ends.

Step 9: Color the basket

Step 10: Prepare a bottle

• Make two cuts on opposite sides of the bottle - each horizontal cut approximately 10 cm long.
• Insert the bottle into the cage. Bend the wires of the poles inward to insert part of the bottle above the cut.
• A small drainage hole will need to be drilled at the bottom of the bottle. If the bottle has a “scalloped” bottom, you need to drill holes in the bottom of each “scallop”.

Step 11: Fill the feeder with seeds

Funnel helps speed up the process. Now you can hang up the feeder and invite all feathered friends in the neighborhood to a picnic.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

And this is a twine net feeder

Necessary materials:

• 2 liter plastic bottle - empty, washed and air dried
• 2 meters of twine
• 2 large rubber bands
• 3-4 large plastic coated paper clips
• 2-3 spins
• medium funnel

Operating procedure

1. Wrap the end of the twine around the neck of the plastic bottle. Push one end through the bottom. Then wrap the twine around the neck again and return to the other end.
2. Gather all the ends and twist together.
3. You need an extra piece of twine to form a loop.
4. Slide the large rubber band toward the neck to hold it tight.
5. Unfold 3-4 large plastic-coated paper clips to make hooks at both ends. Attach each paper clip to the rubber band on the saucer.
6. Attach the remaining ends of the paper clip to the rubber band that is around the 2 liter bottle, evenly spaced at equal distances.
7. Pour the feed with a funnel.
8. Hang on a tree. Yes, make a few small holes in the bottom of the saucer so that the water drains.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Or another similar wire mesh feeder.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Cheap bird feeder

Everyone likes to watch the cute bustle of birds in their yard, with them it is somehow more fun. In the end, they make life worth living! But not all birds like to eat seeds from the ground, especially if there are many dogs or cats in the yard where they dine. The presence of a bird feeder makes life easier for our feathered friends, well, didn’t they deserve it. The great thing about this feeder is that it can be made from materials that you most likely just roll around the house.

What is needed to make a plastic bottle feeder:

• 1 or 2 liter plastic bottle
• Sharp knife
• Dowel with pencil
• Thin flexible wire - approximately 1 meter
• Pair of pliers
• A mesh box-sized cell with relatively small openings

Making a feeding trough is very simple, although there are not many photos, but everything should be clear. And if you are interested in the details, you can read on the site. When you hang up the feeder, wait until the birds have the courage to explore this strange device that provides free food!

• 
• 
• 
• 
• 
•  

Plastic bottle feeder on PVC pipe

Such a thing is very easy to do. You will need one 2 liter plastic bottle and PVC pipe. From the tools:

• drill,
• hacksaw,
• glue,
• knife or scissors.

The first thing to do is cut a piece of pipe across the width of the bottle. This will be the feed insert. (see photo)

Then drill 3 x 8 mm holes in the pipe.

Then make two holes on both sides of the bottle and insert the tube into
hole.

Glue the PVC pipe to the bottle.

Then you need to make a hole in the bottom of the bottle for a long pipe, which will serve as a support for the feeder. Make a perch as shown in the photo. For this purpose, you can use a metal bar. It remains to install the pipe. You can make a foundation and cement, but this is not necessary, the design is very light.

Window feeder from a plastic can of yogurt

You will need:

Jar of yogurt, scissors, thread, bamboo stick and something sharp (screwdriver, but use a drill if you have one!)

How to do:

1. Cut the bamboo stick in half.
2. Make 4 holes in the jar, this is for inserting bamboo skewers!
3. Insert X-shaped bamboo skewers.
4. Take a long piece of fishing line and cut into 4 pieces of the same length.
5. Tie a fishing line on bamboo skewers, and then make a large loop at the end.

The feeder is ready. Hang on a window or on a tree.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to fill a vertical bird feeder without loss

This example shows how to make a container to fill the feeder. The project is designed specifically for long cylindrical feeders that hang vertically and are filled from above. What is the idea. With this thing you only need to fill the container, in this case the prepared plastic bottle with the necessary amount of feed, open the top of the feeder, insert the neck in the hole, pull the thread and that’s it.

Materials

• A clean, empty plastic bottle with a neck diameter of approximately 2.5 cm.
• Tube or material 10 × 10 cm
• rubber or similar adhesive suitable for plastic
• Durable thin rope 60 cm
• Knife or scissors

Step 1: Cut the bottom of the bottle
Step 2: Make a fork. Define the center of the inner tube. Find where to cut the wedge 90 degrees from the inner tube so that the tip of the wedge is in the center and one side of the wedge intersects the corner of the square of the inner tube.
Step 4: Mount the plug. Fold the square corner to fit the opposite corner. Make a cone-shaped bowl (inverted pyramid) with a cut inner tube. Where the parts stack, apply glue. Put the end of the cord into the glue. Fold the pieces. Hold and let dry.
Step 5: Download. When the fork is ready, that is, the glue has dried, dip it into the bottle. Then fill the bottle with feed.
Step 6: Filling the feeder. With your free hand, open the top of the feeder and insert the neck into the hole. With the same hand, pull the cord and pull out the plug. The feeder is neatly filled, nothing will crumble, and all the food will get where you need to.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Original bird feeder

Feeders, of course, are different, but how do you like this option?

It is done very simply. First, find an even piece of bark. Take a plastic bottle and cut the bottom. Fasten the bottle to the cortex with screws. Make a food bowl from the bottom of another bottle.

Then tie the structure with twine, as shown in the photo, and use the screw in as a hook for hanging the feeder.

The last step is to hang up the feeder and fill it with bird food. You can use another piece of bark to stabilize the part screwed in the “bowl” and make an extra perch ...

Materials used for this project:

• Bark,
• 2 screws 5 cm each

• 
• 
• 
• 
• 
• 
•  

Bird feeder from a plastic bottle 200 photos

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•