Bed with drawers for storage. DIY 800 photos, step-by-step instructions

 

Do-it-yourself single bed with drawers

This single bed with storage drawers Perfect for any room! It can be said a large chest of drawers with 6 drawers. It is very simple to make the headboard and footboard - definitely a job for beginners. There are several modifications here, which make this bed unique. First trim the headboard and footrest panels to 80 cm. For most of this bed, Purebond plywood was used! Fasten the plywood to the 1 × 4 boards. Cut the 4 × 4 bars. Now for the cabinet with drawers. Here the base length is 191 cm. To add dividers, simply measure 65 cm from each end and fasten it through the pocket holes of Kreg Jig and 1 screw with 6 mm. The drawers are approximately 58 cm long, but better to measure and cut along. To make a beautiful design, cut the entire body at an angle of 45 degrees. Then, with wood glue and trim nails, secure the cabinet around each drawer. You can see that the housing is completely flush with the top and bottom of the bases. The ends are on the same level, and for the central drawers you can align the housing with the middle dividers. Before putting them together, apply two coats of cream latex paint. Add cute pens. See the master class below for step-by-step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

One and a half bed with storage drawers

This example shows how to do DIY storage box. The very first step is to assemble the front and rear frames of the bed. Attach the corners first and then the center pieces. Once the side frames are made, attach them to the front and back panels. The Kreg rectangular clamp is very useful for this part! It is like having an extra hand to hold something. After that, collect the skids for the boxes. Most parts are fastened with pocket holes and screws, as well as Spax glue and screws. Having completed this part of the bed, go to the drawers. It is very simple. The sides are made of 1 × 6 boards, which are fastened with screws with a 1.25 ″ pocket hole. The base is Purebond plywood glued and nailed to the side frames. Now about the headboard. It is simple and much faster than a bed. Start by cutting 2 × 3 bars and making pocket holes in the bottom of each side. They will be used to fix the headboard to the bed. Then close the boards in each direction using screws with pocket holes. Raise the headboard to add 3 backboards. To read the full instructions, how to make a bed with do-it-yourself drawers, use the link under the gallery. See the master class below for step-by-step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make a bed with storage drawers

Storage in the bedroom is a problem for many. If you need a good idea, see an example, how to make a bed with do-it-yourself storage boxes.

This platform bed is the answer to all problems because it has six large drawersin which you can pack shoes and everything else that takes place.Very detailed instructions on how to make a bed with drawers can be found on the website, the link can be found under the gallery. Detailed master class, see below for step-by-step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Wooden bed with storage drawers

This bed option is a sleek, low modern bed with four large storage compartments hidden behind sliding doors. Storage bed broken into four identical plywood blocks. Each unit is reinforced with an inner rib, equipped with a shelf and has two sliding doors made from old radiator caps. The platform nature of the bed gives good, even support and eliminates the need for a spring box for the mattress (saving money!). The design is assembled from high quality plywood, which increases the cost.

In fact, a little plywood is needed, so you can replace it with cheaper grades to save money. Here, where possible, 1/2 "instead of 3/4" sheets were used to reduce weight and costs.

This whole project was done only with the help of a circular saw, but if you had a table saw, it would be faster and more accurate. At the expense of sawing, you just need to know single box design. Repeat four times for the entire bed. The sizes here are for a one and a half mattress, you can adapt them to the sizes of your own mattress. Cut one panel out of plywood 3/4 "measuring 81 x 106 cm (top); one panel measuring 81 x 35 cm (one side); one panel 1/2" at 81 x 35 cm (second side); one 1/2 "panel at 104 x 35 cm (stiffener); one 3/4" panel at 104 x 8 cm (doorway) and one 1/2 "panel at 104 x 45 cm (shelf). Further assembly sequence beds with storage drawers read on site. See gallery step by step photos below..

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed with lower drawers

See an example of how to do platform bed frame with storage bins. Dimensions are 140 wide and 194 cm long (each box 96 cm) and 37 cm from the wheels to the top of the bed (height). Bed with lower storage drawers ideal for a small bedroom and offers much more than just a bed. The design provides a lot of space for storage and equipped with wheelstherefore the bed is easily pushed away from the wall to do the cleaning. You can make a bed from boards, this is a good option, but expensive. In this case, to be cheaper, MDF was used. For the bed, 4 sheets were needed, which is much less than the price of a natural tree. Besides, if you are going to paint a bed, a real tree will be just a waste of money. This is a simple design, in fact, just two big wooden boxestwisted together. The round wooden pieces at the bottom of one box are the supports that hold the middle of the bed so that it does not sag. Master class, how to assemble a bed with lower drawers, look at the step by step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed with drawers for storage

This guide shows how to make a bed with do-it-yourself drawers. This is a simple structure that can be assembled using conventional carpentry tools and available materials.

The list of materials and sawing with sizes is in the article, the link can be found under the gallery. The build process can be viewed on step by step photos in the gallery. If you have questions, be sure to watch the video on the site.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

DIY storage bed

If you have little space, you should look for various compact solutions, including dual-use furniture. For a bedroom, for example, maybe storage bed, this is the piece of furniture that takes up the most space in the bedroom. This instruction shows how to make a DIY storage bed for much less money than they are sold in the store. This allows you to use the space more efficiently and keep everything clean and tidy. Project is a bed queen size and has six drawers.

The bed is very durable and will last for many years. Take the time to complete this project to perfection, as you are likely to spend 1/3 of your day in this bed every day.The assembly procedure for the bed frame and drawers is shown in great detail in the master class on step by step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

High crib with storage drawers

A practical solution for a children's bedroom, see how to make a bed with do-it-yourself storage boxes. Before you begin, make a plan for the size of the block and do not forget about the mattress at the top. Start by marking on the wall, using the spirit level, the top height of the frame, do not forget that there will be 18 mm MDF sheet and mattress. After marking with a pencil, this will be the guide line for the upper frame. Install the crossbar under the line and drill through holes. For extra strength, drill holes every 250-300 mm.

Then install the plastic plugs. This is the beginning, how to further assemble the crib with drawers, read the full instructions on the site. The master class is shown below in step-by-step photos..

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make a platform bed with a storage niche

Carved from plywood and adaptable to any size mattress, this plan platform beds Eliminates the need for a spring unit and adds plenty of storage space.

The site has detailed instructions, how to make a bed with your own hands, as well as a complete list of materials and tools needed to work on the project. If there is a need to better understand the principles of assembly, can watch the video. Below in the gallery are presented several step-by-step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself double bed

The bed shown in the photo has been around for five years, and it is still just as sturdy and durable. If you want to do the same do-it-yourself double bed, instructions on the author’s website and step-by-step photos below in the gallery are at your disposal. This is a great solution if you do not have a chest of drawers, or if there is not enough space where to put it. Then these storage boxes great for you. Actual instructions are divided into 4 sections. They refer to a king-size bed frame, but you can change to a queen-size bed frame if necessary. You just need to make it 40 cm narrower, and the length of the bed frame remains the same.

Here are some more ideas - you can remove the center console or reduce the depth of the drawers by 20 cm. You will also have to reduce the head and footboard by 40 cm wide. See step-by-step photos of all four stages below for step-by-step photos. Good luck to everyone who does this!

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

High bed with storage

Here's an interesting way to use raised platform racks. With ample storage space, this is an ideal solution for a child’s room when it is necessary to maximize the area. Here 5 shelves were used as a base, arranged so that there were no gaps along two open sides. Make a box for the bedby cutting boards measuring 15 x 198 cm (2 each) and 15 x 102 cm (2 each). Bed boards were fastened with screws through the ends and corner brackets on the inside. To prevent the mattress and bed from moving, the case is attached to three bookcases with wall mounts. The author used double bed trims for support and two flat metal rods that were taken from another project to support the slats in the gap between the shelves. The shelf in the front middle part is not fixed, so we can pull it out and get to the shelves in the back for long-term storage items, such as winter clothes and the like. Not the easiest project, but can be done, so this is not wasted space.

• 
• 
• 
• 
• 
•  

Stock bed

Bed with lower drawers and medieval pillars as a headboard. Pretty stylish design.

Any bed is just a frame for a mattress. Like most beds, this one consists of a removable headboard, foot, side rails and support beams. The design is easy to scale for long types of mattresses or wider. Although in this case, an additional support beam in the center may be required. How to make a bed see below for step by step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make a bed with drawers

You think how to make the most rational use of the free space in the bedroom? Do not forget about the main subject, which occupies the most square meters. therefore bed with drawers for storage, just there is that optimal solution. How to make a bed is described in great detail in the instructions on the site, which you can read using the link under the gallery. See the master class below for step-by-step photos..

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Built-in bed with drawers

Many do not have space for a large bed, but if you have a corner space, then the problem can be solved. With some modifications you can make a built-in bed do-it-yourself. And if you save meters, it’s better make a bed with storage drawers. Here's how in this example - huge niches on a steep wooden drawer system, which is very easy to manufacture and incredibly durable. To build this design, Craig Jig was used. If you do not know what Kreg Jig is, watch the video on the site to understand how it works. First make the front bed frame. Use glue between each joint. Then move on to the back frame, which is made of 2 × 3 and 2 × 4 boards. Now it's time for the drawer slides. You make T and L using glue and wood screws. To fasten, squeeze the pieces together. Be sure to pre-drill holesto prevent wood splitting. Before attaching, make pocket holes for each piece. Next, attach the drawer slides to the frames. The photo shows that the rear frame is fastened with screws with 6 cm pocket holes, and the front one with screws with 3 cm pocket holes. After all 4 are attached, make fastenings that will support the mattress and keep the drawers from tipping over. See assembly sequence in master class in step by step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Contemporary bed with drawers

For all amateur craftsmen and those who work on weekends, here is your guide to making modern style beds with drawers for storage! This version of the project was made entirely of plywood, but to save time and effort, you can buy pre-trimmed lumber or use other material. Do not be afraid to adapt these plans to suit your needs, including changing the lattice pattern of the cladding, changing the manufacturing method for certain parts, as well as the color and style of decoration. The bed consists of 3 main parts: the left half, the right half and the headboard. To support the weight of the structure and tie the left and right halves together, there are three supporting structures. Each half has its own lower support frame, and a large frame will lie on top of both halves when they are assembled together. Now cut the 2x4 bars in the following sizes: 6 pieces of 200 cm, 9 pieces of 132 cm and 10 pieces of 57 cm. Then, using a pocket hole clip, drill 2 holes at both ends of each middle plank (132 and 57 cm).

Attach the middle rails to the 200 cm rails to create two small support frames (5 middle planks each) and one large support frame (9 middle planks). Then cut the plywood, see the sizes of the parts on the site, otherwise it is a big list. Recommended saw the plywood into long strips, and then use the transverse sled to cut each piece in length. The first and most obvious problem of this project is the scale of it all. There are a huge number of steps and parts to consider, and it is incredibly easy to make a mistake. Therefore good to have on hand sketches and parts lists. In addition, it is useful to mark each piece of wood with a pencil and, accordingly, in the drawing. In conclusion, this project can be fascinating for those who want to improve their woodworking skills. To avoid mistakes and create a product that you can be proud of, just remember that you need to act more slowly and pay attention to each step.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed with lower drawers and built-in nightstands

This bed platform with built-in nightstands and drawers made to order in the workshop. The requirements were such. The first is to equip the structure with two side low bedside tables in the form of pencil cases for small items. Second, the bed should have drawers, as it turned out, you can see in the photo. And third, the condition that the edges are rounded. How all this was done in practice, you can see in a detailed photo report. Slight difficulties arose with side cabinet drawers.

How this problem was solved can also be read in the instructions on the site. See below for step-by-step photos of bed assembly.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

The bed was made in the workshop of Marko Studio

Do-it-yourself chest of drawers

Finding the right design to create extra storage space in a tiny bedroom is not always easy. It’s probably worth turning on your imagination and being creative. So look at an example, how to make a dresser bed do-it-yourselfthat can solve the problem of a small bedroom, both in aesthetic and in practical terms. First assemble the headboard and footrest. The side bars are as follows. One will be a solid sheet of plywood made of solid wood, as it is attached to the chest of drawers. The other must be cut off. Do not forget to add pocket holes at each end of the railing. They will be used to attach the guides to the headboard and footboard. Then attach the bed frame to the side rails as shown in the photo. Use wood screws and glue. And the last step is the assembly headboards and footboards. You will also need wood glue and pocket holes for screws. You can read about all this on the site, and Master Classhow to make a bed chest of drawers with your own hands, see below for step-by-step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed frame with storage

Here is another example of how assemble the bed frame with storage boxes do it yourself. Depending on the size of the bed, you need to make a frame of two equal sections. This king size bedtherefore sections are approximately 200 x 100 cm. The main reason for having two sections is for mobility purposes. The frame is made entirely of 2x4 timber with a margin of 10 cm. The height of the frame is 38 cm. You can make the frame in any configuration you want, just make sure that there will be enough space for drawers in it. Align the two sections on top and fasten them with bolts. Do not over tighten, because you still have to disassemble the structure to move the bed into place. Detailed instructions can be found on the website. See below for sketches and step-by-step photos..

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Teenage bed with do-it-yourself drawers

Make DIY storage box beneficial in many ways. In addition, it will be much cheaper than buying in a store, but this is an excellent option for several more reasons. First of all, there will be where to put the shoes, of course, this does not mean that you will definitely put them there, there are many other things that need a place to store, but as a version, a good option. Secondly, now nothing will roll under the bed and will not disappear forever, or at least until the general cleaning. Finally, a good bed, it is beautiful and comfortable. Instruction how to make a teenage bed with storage drawers read on the site.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Storage bed with folding footboard

Here is another example how to make a wooden storage bed with your own hands.

In fact, this is a standard design for this type of bed, but with one feature. The author of the project developed a plan for making hinged footrest, which would lock in place and give access without having to remove the mattress and trims. How to do this, read the instructions on the site.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself couch with headboard

It is best to relax under a blanket best on your bed. Designers especially for lazy people who don’t want to make and make the bed, came up with a couch. You can flop on this element of interior without changing clothes. At the same time, put a pillow under your head, get comfortable and you can relax. Are you interested in such an idea? Then read the instructions, how to make a comfortable couch with a headboard and do-it-yourself storage boxes.

Not only convenient, but also practical. By the way, the size of the couch can be varied for any room, even the smallest.

• 
• 
• 
• 
• 
• 
•  

Bed with drawers and lighting

The idea was to make inexpensive storage space under the bed. The author used four tables, two for lighting and two for things that can be easily reached while in bed. A cheap wood was used to cover the two sides of the tables on the side of the lamps and the three sides on the side of the shelves. it helps make the table very tough, support weight and move in bed. Also been used reflective plastic sheetpurchased at a store that has been fixed inside tables, as shown in the photograph. The author made shelves from the other two tables, although this is not a good idea. It’s not very convenient to reach out and the niche is too deep.
9 mm sticks, lightweight fabric and staples are used to cover the lights. Switches are located at the head of the bed. They are not very beautiful, but also not very noticeable, which was intended. The bed itself is bolted to the tables. Electric wires go under the mattress.
The boxes are fastened with special screws so that they are recessed into the tree. The author used them backwards, the screw goes through the wood, so that the boxes can be taken apart. Under the drawers there is woolen pads, that they glided across the floor. BoxIki just fit under the bed. They are not intended for everyday use, they store things that are needed from time to time. The author of the project has been using this bed for more than a year, and it is absolutely stable and reliable.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Storage boxes under the bed

If you do not have the opportunity make a bed with storage or you already have a regular bed, you can always make storage boxes separately. It is very convenient and functional, and if it is still beautiful to design, then it is stylish. Look below eight exampleshow to make do-it-yourself storage boxes under the bed.

Box under the bed for storing things

The space under the bed is one of those places that is often underused or clogged with toys or dirty clothes. There are many ideas on how to solve this problem. For example, you can make these boxes. These boxes not only give you plenty of storage space, but they look just amazing at the same time. Boxes are inexpensive to make and easy to assemble. This project is a great option for beginners, you will need very few supplies and you can complete the work in one day.

Now your little ones will have enough space to store their clothes, toys, books and much more!

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

DIY storage bins under the bed

These folding under the bed storage boxes - The ideal solution to save space where you can store shoes, bags and other things that are inconvenient to store in the closet! Measure the width and height of the space under the bed frame. Then cut the tree into four parts. Purpose - make a box of rectangular shape, the longer parts will be the sides, and the short ones will be the front and back. Pre-drill two holes at each end. Fold two sets on top of each other to save a little time! Gather the corners of the drawer and glue with wood glue. Attach the two ends to each other at an angle of 90 degrees. TIP: Use the clip for the angle brackets. Do it at all four corners until you get a rectangular box! Cut the plywood with a jigsaw or circular saw to make the base. Screw the base into the frame of the box. Then screw the wheels to all four corners - and voila, you have a box that rolls. By the way, when measuring the size of boxes - do not forget consider wheel size!
Now decor. You can just stick the wallpaper on the inside of the drawers. And then the pens! Screw them to the front of the box, after drilling holes in the center. Remember to measure the width and height.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make storage boxes under the bed

To provide extra storage space under the bed, see how to make simple plywood boxes on casters.

Boxes are very simple to make with your own hands, you can even attract your children as assistants and paint them together to your liking. A small instructions with lists of materials and sawing can be read on the site. Step-by-step photos of the master class, see below in the gallery for step-by-step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

DIY storage drawer

These cool drawers with platinum baskets are perfect for organizing things in the kids room! Read how to make do-it-yourself storage boxes under the bed and add more space in the children's bedroom (although they will fit in the space for adults)! Start with the wood you will use and size. You will need everything yourself calculate for your bedbecause each bed is at a different height from the floor. Here are some tips to measure. Measure from the floor to the bottom of the bed. Then determine the width of the tree you can use, adding the dimensions of the wheels and the thickness of the plywood at the bottom of the bed. Here the rollers are 4 cm high and the side boards are 15 cm. Thus, the height of the drawers is 19 cm. The final dimensions of the drawers are as follows. The front of the drawer is 94 cm. The sides are 61 cm. This is the size by which the plywood was cut because it is screwed to the bottom of the drawer frame. Details of the instructions, as well as a list of necessary materials can be found on the website, a link under the gallery. Yes, add more bumpers for boxesso that when the children close the drawers, they do not hit the bed.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Boxes for storing things under the bed

If you are looking for a way to organize storage under the bed, which will be not only functional, but also beautiful, this guide is for you! The perfectionist's dream has come true! This example will show you how to make do-it-yourself storage boxes under the bedIt is very comfortable and suitable for any bed. Drawers also have cute handles that perfectly match the style of the room, but of course you can change them if you want. You can also work with the main design and make any necessary changes in size so that you can change them to suit your space. Also these storage boxes are universal. You can install them under a bookshelf or TV stand ... or in a children's playroom. They can really be used wherever there is space to fit them in. For one box you will need the following materials:

• 3/4 plywood sheet or MDF for the base (here dimensions 56 x 56 cm22), if you plan to paint the boxes, you can use the board
• two sheets of mdf
• 4 wheels
• drawer handle
• staples
• eight wooden planks for angle brackets
  
  
  • 
  • 
  • 
  • 
  • 
  • 
  • 
  • 
  • 
  • 
  • 
  •  
  View the embedded image gallery online at:
  https://i.expert-h.com/en/krovat/1134#sigFreeId5366269833

These boxes are made of plywood, covered with wallpaper (optional) and have beautiful handles. In addition, they roll, which means that they are very convenient to use! Ready each box is 60 x 90 cm. Before you begin, measure the height of the bed frame from the floor to the lowest beam to determine the height of the drawer. The height of the bed frame from the floor to the lowest beam, as well as the height of the rollers will determine the position of the elements. Measure the height of the bed frame from the floor to the lowest beam and roller height from the bottom of the wheel to the top of the mounting plate. Using a tape measure and a pencil, measure the distance from the top edge of the box down from the inside and make a mark. However, you should read the instructions on the site, it is a bit long.

• 
• 
• 
• 
• 
• 
• 
• 
•  

Here is another example how to make simple drawers with storage handles under the bed from cedar boards. Beautiful, functional, and great for off-season storage or for everyday use - fill them with everything you want and enjoy your little hidden store! Cedar has a natural resistance to insects, it smells great and looks very beautiful! Make a base by attaching the boards with glue and screws. Required pre-drill holes around the perimeter for mounting sides. Attach the long sides to the base, then the short ones. Sand and apply clear polyurethane if you wish. Attach the casters to the four corners, and the handle to the center of the front of the drawer. I hope you enjoy this project and you will now have storage space under the bed.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Chest drawers for storage under the bed

Want to throw away your old chest of drawers? Before moving it to the curb, leave a couple of drawers for storage. You can set the wheels below, one in each corner, and you will get a great storage box under the bed. In addition to using them as storage under the bed, drawers on casters will work well under a bench for shoes, under a coffee table, toys, etc. The main thing is to make such drawers is not at all difficult, and a lot of benefits will bring. How to do it, see below for step by step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Beds with drawers for storage 200 photos

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•