Do-it-yourself bed made of wood

DIY single bed drawing

An example with drawings how to make a bed from pine boards in a rustic style! Drill pocket holes around the side and top edges of both plywood panels. These holes are for fixing the legs and top. Then add upper and lower facade. Attach the rails from a distance as shown. Then attach the long legs to the head and add a top trim. The footboard is the same as the headboard, only the legs are shorter. Then you need to do side railing. If you have a spring mattress, it is essential that the spike is attached in the lowest possible position. Without block of a mattress - using a plank system, you can attach the cotter pin to the maximum position possible - 3 cm down from the top edge. Attach the side handrails to the headboard and footboard. Note. To facilitate assembly or disassembly, you can buy a special bed for attaching side handrails. And finally, add slats or a board under the box of the mattress.

Sawing with dimensions

• 2 sheets of plywood 3/4 "size 24" x 37 1/2 "(61 x 95.5 cm)
• 4 boards 1x4 long 37 1/2 "(95.5 cm) paneling
• 12 1x3 boards, 17 ”(43 cm) long
• 2 2x4 bars, length 48 1/2 "(123 cm) headboard legs
• 2 2x4 bars, 29 1/4 "(74 cm) long;
• 2 boards 1x3 long 45 1/2 "(116 cm) the top of the footboard and the head of the bed
• 2 2x8 boards 75 ”(190.5 cm) long side rails
• 2 x 1 ”x 75” (190.5 cm) long slats

Assembly sequence shown in the diagrams, as well as several photos with examples of beds made according to this manual.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Single bed dimensions drawing

Presented here do-it-yourself single bed drawings of wood. The frame is made of bars and planks 2 × 4 and 1 × 4. Considering the traditional and simple design, this bed can fit the style the interior of any bedroom. In addition to conventional carpentry tools, you will also need a good Miter sawto make corner cuts. The chart on the right shows the details of the sawing bed, indicated by letters.

A - 2 bars 4 × 4 25 "(63.5 cm) long, 2 parts - 37" (94 cm) legs
B - 4 boards 1 × 4 39 "long (99 cm), 2 parts 2 × 4 25 inches long (63.5 cm)
C - 1 block 2 × 4 length 48 "(122 cm)
D - 4 boards 1 × 4 length 39 "(99 cm), 8 parts 2 × 4 length 19" (48 cm)
E - 2 boards 2 × 6
F - 2 bars 2 × 2, length 75 1/2 "(192 cm), 17 pieces of boards 1 × 4, length 39 3/4" (101 cm) length of auxiliary strips

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawing of a wooden bed with a headboard

A simple example with step-by-step instructions and drawings on how to make a wooden bed with a headboard yourself. On the right in the picture is a diagram where all the parts are marked with letters, below you can see the sizes of these parts.

Instruction how to make a wooden bed can be read on the site. In the gallery, the diagrams show the assembly sequence.

A - 2 bars 4 × 4 with a length of 52 ”(132 cm), 1 board 2 × 4 length 45 1/2” (116 cm), 1 board 2 × 6 with a length of 47 1/2 ”(121 cm)
A - 7 boards 2 × 6 29 ”long (74 cm), 4 boards 1 × 4 38 1/2” long (98 cm)
B - 2 bars 4 × 4 22 ”(56 cm) long, 1 board 2 × 4 45 1/2” (116 cm) long, 1 board 2 × 6 47 1/2 ”board (121 cm)
B - 7 boards 2 × 6 16 inches long (41 cm), 4 boards 1 × 4 38 1/2 inches long (98 cm)
C - 2 boards 1 × 10 length 76 1/2 ”(194.5 cm)
D - 2 boards 2 × 4 - length 79 1/4 inches (201 cm), 2 boards 2 × 4 - length 35 3/4 inches (91 cm)
E - 16 boards 1 × 4 length 38 1/2 ”(98 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Classic bed drawing

Walkthrough with drawings, how to make a classic wooden bed with your own hands. Of the basic tools you will need mitral saw and jigsaw. For the manufacture of the bed, 2 x 6 boards and 4 x 4 bars are mainly used. Also, do not forget to prepare wood filler and stain. Full list of necessary materials and tools can read on the site. Below is the sawing up of the bed according to the diagram in the picture on the right.

A - 2 bars 4 × 4, length 52 inches (132 cm), 2 pcs. 15 1/2 in. (36.5 cm) long
B - 4 boards 1 × 6
C - 13 boards 2 × 6 length 36 1/2 ″ (93 cm)
D - 2 bars 2 × 4 - length 78 1/2 ″ (200 cm), 1 board 2 × 6 length 80 1/2 ″ (205 cm)
E - 2 boards 2 × 10 length 80 1/2 "(205 cm), 1 piece - 71 1/2" (182 cm), 1 board 2 × 6 length 71 1/2 "(182 cm) side bars
F - 3 bars 2 × 4 length 80 1/2 "(205 cm), 14 boards 1 × 4 length 76 1/2" (195 cm) auxiliary strips

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawing of a classic wooden bed

An example with drawings how to make a classic wooden bed with your own hands.

Schemes and several step by step photo build See below in the gallery.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawing of a simple wooden bed

In this example you can make a simple wooden bed do it yourself.

A few points of assembly. Note that the slats rest on the protrusion. inside side guides. When assembling the head of the hole for dowels, it is best to drill by holding the head and drilling the hole to the end from the outside, as shown in the diagram. The footboard is almost identical to the headboard. If you prefer to put your feet from the end of the bed, move away from the upper horizontal part and make racks only 45 cm in length.

The beams of the bed have a number of blocks at the inner corners. The goal is to distribute the slats and prevent them from slipping.

It is best to glue and screw the 38 x 38 mm support for the bar onto the main part of the rail to ensure it secure mount. Bed frames are generally designed for disassembly and movement. For this frame, you just need to unscrew the side guides. The slats are located between the bed guides and held only by gravity. The blocks on the bed rails prevent them from slipping. Drawings and schemes with step by step photos, see below in the gallery.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make a bed of wood do-it-yourself drawing

This bed is ideal for children and adults. Using these drawings make a wooden bed do it yourself it will not be difficult. The first step is to make the legs. Two high legs will be part of the head, and two short parts of the footboard. Side rails - these are 2 × 6 boards, attach them using glue and 6 cm screws for pocket holes. Then make the footboard so that the top, also a 2 × 6 board, is aligned flush with legs. Attach the headboard panel to the legs using glue and screws with pocket holes. The top of the trim will be flush with the top of the legs.

Then attach the guides to the headboard through the holes in the pockets on the guides and in each leg. Attach the footrest to both legs, making sure that all the top and sides are are on the same level. Time for the slats! Here we used bars 2 × 2 boards for this part, fixed with glue for wood and 8 cm Spax or wood screws. It’s best not to use glue to attach the slats and runners to the footboard and head of the bed so that you can move the bedfrom room to room and disassemble if necessary. Below see photos and drawings with dimensions.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Single bed from an array of drawings

Presented here solid single bed drawingmade by yourself.

This project was developed using the dimensions of used lumber. Adjust the size as needed.

If you will also use old boardswash them with warm water, dish soap and a brush. Allow the tree to dry completely before sawing. Very detailed assembly instructions can be found on the website of the author of this project. Drawings, diagrams and step-by-step photos can be viewed below in the gallery.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

King size bed sizes

An example with drawings, how to make king size bed do it yourself. This size is borrowed from the Americans and is essentially almost square design approximately 2 x 2 meters. Pretty impressive, and therefore translated as a king bed. On the right in the picture is a diagram where all parts of the bed are indicated by arrows with letters, and below is a list of these parts with dimensions. Walkthrough can be read on the site.
 

A - 2 bars 2 × 2 - 35 inches (89 cm) long, 1 pc. 78 inches (198 cm) long, 1 pc. 75 inches (190.5 cm) long, 1 board 2 × 6 75 ″ (190.5 cm) long
IN - 2 boards 1 × 6 75 "(190.5 cm) long support
C - 9 boards 1 × 6 20 inches long (51 cm), 8 slats 1 × 3 20 inches long (51 cm)
D - 2 bars 2 × 2, length 13 1/2 "(34.5 cm), 1 pc. 78" (198 cm), 1 board 2 × 6, length 75 "(190.5 cm)
E - 2 boards 2x8 length 79 ″ (201 cm)
F - 2 boards 1 × 6 79 "(201 cm) long, 1 board 2 × 6 79" (201 cm)
G - 14 boards 1 × 4 75 inches (201 cm) long

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself wooden bed with headboard

This durable wooden bed will last for you for many years. Here how to make a bed with a headboard do it yourself.

• The first step after making cuts for the headboard boards is to make pocket holes. Used here K5 Kreg Jig. This is not the cheapest option, but the most convenient.
• Saw boards and fasten with screws with pocket holes.
• Then attach the boards to the legs of the headboard. The legs are 2 × 6 boards. Add glue to each leg and attached to the sides of the board using screws with holes for the pocket through the boards and into each leg.
• Lastly, attach the top of the headboard.
• Lay out two boards for the footboard evenly. Attach them with pocket hole screws.
• The legs are attached in the same way.
• The top board is a 2 × 2 block attached with screws with pocket holes through the top board and block.

The crossbars are made by attaching a 2 × 2 stud to a 1 × 8 guide using glue and Spax 2 ″ screws. Before attaching the boards, make pocket holes at each end. And finally, collect all the parts. Complete instructions how to make a wooden bed with a headboard do it yourself read on the site. See below for step-by-step photos and assembly diagrams.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed platform

A simple project with step-by-step instructions on how to make a full-sized bed platform with a beautiful do-it-yourself design. The first stage is the assembly of the frame. The next step is to install 2 × 2 strips. Use spirit levelto make sure the spikes are horizontal. Then install the 1 × 4 support bars on the studs so that create a flat surface. Position the planks at the same distance, leaving a distance of 3 cm between them.

Make legs from 2 × 4 bars. Substitute legs under the middle barto maintain weight and increase the rigidity of the bed frame.

A - 2 boards 2 × 6 57 inches (145 cm) long, 2 pcs. 75 inches (190.5 cm) long
B - 3 bars 2 × 2 75 inches (190.5 cm) long
C - 16 boards 1 × 4 54 ″ (137 cm) long support strips
D - 6 bars 2 × 4 8 ″ (20 cm) feet long
E - 2 boards 1 × 3 length 77 ½ (197 cm), 1 pc. 59 ″ (150 cm) long, 1 pc. 1 × 2 59 ″ (150 cm) long

• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawings how to make a platform bed frame

Step by step instructions with drawings, how to make a do-it-yourself platform bed frame. Anyone can make a simple bed frame if they have not found a suitable model in the store that suits your tastes, or just want to save. In this manual - queen bed frame from wooden boards with simple legs and a beautiful headboard. Assembling a wooden bed frame is simple and can be done by anyone with basic woodworking skills.

A - 8 boards 1 × 6 67 inches long (170 cm), 2 boards 1 × 3 62 inches long (157.5 cm), 2 pcs. 1 × 3 40 1/4 ”(102 cm) long
A - 2 slats 1 × 2 40 1/4 ”long (102 cm), 1 1 × 3 board 68 1/2” long (174 cm)
A - 2 boards 1 × 3 41 ”(104 cm) long and 1 pc. 68 1/2 ”(174 cm) long
B - 4 bars 4 × 4 - 6 inches (15 cm)
C - 2 boards 2 × 6 length 80 1/2 ”(205 cm), 2 boards 2 × 6 length 63 1/2” (161.5 cm)
D - 2 bars 2 × 2, length 80 1/2 ”(205 cm)
E - 16 boards 1 × 4 - 152 cm plates
F - 2 boards 1 × 3 83 ″ long (211 cm), 2 pcs. 1 × 3 65 1/2 ″ long (166.5 cm), 1 plank 1 × 2 65 1/2 ″ long (166.5 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

DIY bed frame drawings

Simple and cheap wooden bed frame is an easy project if you have correct drawings. Assembling a frame from a tree is quite simple, especially if there is at least minimal experience, since you just need to saw the components in size and tighten with screws. It is also necessary to pay attention to details, because all parts must be aligned at both ends. See part sizes below.

Sawing parts

A - 4 bars 4 × 4 long 6 ”(15 cm) legs

B - 2 boards 2 × 12 length 63 1/2 inches (161.5 cm) and 2 pcs. 80 1/2 in. (205 cm) long

C - 3 bars 2 × 2 length 80 1/2 ″ (205 cm)

D - 17 boards 1 × 4 - 152 cm plates

E - 2 boards 1 × 3 - length 85 1/2 ″ (217 cm), 2 pcs. 65 1/2 ″ (166.5 cm) long

• 
• 
• 
• 
• 
• 
• 
•  

Drawings and schemes of the platform bed on wheels

If you like industrial stylethen here is a good option platform beds with metal rollers. The mobility of the frame makes it easy to repair your room as often as you want.

How to make a platform, shown in diagrams in the gallery. On the site you can read the instructions, as well as lists of materials and sawing with dimensions.

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself wooden bed drawings

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawing bed with drawers

This bed, reminiscent of an old chest, looks much more complicated than it really is. The design is bed one and a half with six drawers (three on each side), as well as parts with metal strips of aluminum 5 cm wide, which can be spray painted before installation.

Drawers occupy almost half the width of the bed to make it larger additional storage space and a little wasted place!

The drawing provides for the use of strips, provided that you will do base for mattress. Three sheets of plywood can be placed in width (with drilled in them vents) for a platform-style bed. The frame of the box is attached to the lower edge of the headboard and footboard. Large metal L-shaped bracketsattached to the head or footboard and the top edge of the drawer frame will provide additional support.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Double bed with drawers

Make double bed with storage drawers not so difficult, especially if you have a good drawing and assembly instructions. The dimensions shown correspond approximately to the mattress. 121 cm long and 198 cm wide. Measure your mattress and adjust the size of the bed. Drawer surfaces depend on the width of the board. Measure and adjust the height of the case to fit these sizes. Drawers are designed for lower guides. If you want to use the side rails, adjust the drawer: width for the sliding gap (usually 15 mm on each side of the drawer).

Material List:

• 5 sheets of 3/4 "plywood or MDF (including drawers)
• 3 boards 1x12 180 cm long (front side of the box)
• 6 boards 1x10 250 cm long (for boxes)
• 5 2x4 bars 250 cm long
• 10 boards 1x2 250 cm long
• 2 boards 1x3 also 250 cm long

Below in the gallery are presented drawings and diagrams of the bed with dimensions in inches, multiply by by 2.54to get the result in centimeters. Following the diagrams are a few examples of beds with storage drawers made according to this manual.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Wooden bed with drawers drawings

These drawings show how to make simple wooden double bed with do-it-yourself storage drawers. Suitable for a mattress measuring 193 cm wide and 205 cm deep - there are different sizes of large mattresses, so please measure your mattress and adjust the size of the bed accordingly. Boxes can be made of plywoodcut into strips 20 cm wide or from 1x12 boards, but this, of course, is more expensive.

In addition, you will need:

• 2 sheets of 3/4 "plywood, cut into strips 40 cm wide (it is very important that all strips are the same width)
• 1 sheet of plywood 1/4 "(also cut into strips 40 cm wide, this is for the bottoms of drawers)

As well as 250 cm long boards

• 12 pcs 1x4
• 6 pcs 1x3 for strips
• 4 things. 1x2
• 6 pcs. 1x8 for drawers
• 2 bars 2x4 250 cm long
• 6 bottom corner mounts for drawers
• 6 pens

The assembly order of the bed with drawers is shown in the diagrams in the gallery

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed with drawers drawing

Presented here drawings and diagrams of a classic bed with storage drawerswhich is perfect for a small bedroom. This bed creates a lot of storage space in a more compact profile. In the article you can find detailed step-by-step plans that will help you make your own do-it-yourself classic-style bed with drawers. Panels are made of plywood (although you can make panels from timber or boards for a more stylish look) The total width is 18 cm narrower than traditional classic beds. The reason is that the mattress on this bed is on topinstead of refueling in a box. So if you have a compact space, this bed will be a great solution for small bedroomsince it includes six huge storage boxes.

For the drawers to work, you must build a perfectly square shape, and all cuts must be square and straight. On the site you can find out what materials are needed for this project, parts list with dimensions and read the detailed step-by-step instructions. See below in the gallery schemes and drawings of the phased assembly of the bed with drawers.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Here, step-by-step photos show how to assemble by the above drawings classical do-it-yourself bed with drawers.

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Below in the gallery you can see the finished projects bed with storage drawersmade according to the above manual.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawings of bed with lower drawers

This is a double storage bed where drawers are located on three sides. Using the drawings presented here, make such a bed with lower drawers not difficult, it’s a practical design that will save a lot of space in the bedroom. Although there are also disadvantages, the drawers are not deep, which means less storage space. But there are many of them. Instruction how to make a bed with storage drawerscan be read on the site. There you will find a list of materials and sawing parts with dimensions.

The assembly order is shown in the diagrams in the gallery..

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Single bed with drawers drawings and diagrams

Example, how to make a single wooden bed with storage drawers. For assembly, you need 3 sheets of 3/4 ″ plywood and one 1/4 ″ plywood sheet, as well as 1 × 4 boards of 250 cm and 1 × 2 length. Carefully choose lumber, making sure that the components are perfectly flat and were in good condition.

On the right in the diagram, all the details are marked with letters, parts list with dimensions in inches and centimeters see below.

A - 4 sheets of plywood 3/4 size 15 "x15" (38 x 38 cm), 4 pieces 15 "x59 1/2" (38 x 151 cm), 2 pieces 12 x 3/4 "x15" (32 x 38 cm )
IN - 2 sheets of plywood 1/4 "measuring 15" x 61 "(38 x 155 cm), 1 sheet of 15 x 40 1/2" (38 x 103 cm)
FROM - 2 boards 1 × 4 61 "(155 cm) long, 13 pieces 7" (18 cm) long
D - 1 sheet of plywood 3/4 "size 61" x 8 1/2 (155 x 22 cm)
E - 2 sheets of plywood 3/4 "size 14 1/4 x 15" (36 x 38 cm), 2 pcs. - 39 "x14 1/4" (99 x 36 cm), 1 pc. Size 12 3/4 "x14 1 / 4 "(32 x 36 cm)
F - 4 slats 1 × 2 length 61 ″ (155 cm), 2 pcs. 40 1/2 ″ (103 cm) long, 9 pcs. 12 ″ (30.5 cm) long

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Queen-size bed with drawers

Here are drawings and diagrams that you can use. make a queen size bed with storage boxes. If not up to date, queen size bed dimensions 160x200, that is, in fact a double bed. It differs from the standard model by about 15 cm. How to make a bed with your own hands, read the detailed instructions on the site. Below is presented sawing boards with dimensions in inches and centimeters.

A - 2 bars 4 × 4 52 inches (132 cm) long, 2 pieces 20 1/2 inches long (52 cm)
B - 4 boards 1 × 6 length 60 1/2 "(154 cm), 11 boards 2 × 6 length 29" (74 cm)
C - 1 block 2 × 4 length 67 1/2 ″ (172 cm), 1 board 2 × 6 length 69 1/2 ″ (177 cm)
D - 2 boards 2 × 6 length 60 1/2 "(154 cm)
E - 4 boards 1 × 6 60 1/2 ″ long (154 cm), 11 boards 2 × 6 16 1/2 ″ long (42 cm)
F - 2 sheets of 3/4 ″ plywood, size 14 3/4 ″ x 80 1/2 ″ (37.5 x 205 cm), 4 sheets of 13 1/2 ″ x 14 3/4 ″ (37.5 x 34.5 cm), 1 pc. 15 ″ x 80 1/2 ″ (38 x 205 cm)
G - 2 bars 2 × 4 length 26 1/2 "(67.5 cm), 13 pieces - 80 1/2" (205 cm)
H - 2 boards 1 × 10 with a length of 14 ″ (35.5 cm), 2 pcs. length 23 1/4 ″ (60 cm), 1 sheet of plywood 1/4 ″ size 24 ¾ x 14 ″ (88 x 35.5 cm)
H - 6 sheets of 3/4 ″ plywood size 25 1/2 x 13 1/4 ″ (65 x 35 cm), 12 boards 1 × 3 25 1/2 ″ long (65 cm), 12 pieces 13 1/4 ″ long (33.5 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

How to make a bed frame with drawers

If you want to use the room’s space efficiently, make a bed with storage drawers do it yourself. Given its simple design, this storage bed frame can accommodate in almost any room, this design will easily match the style of existing furniture. Just make sure you leave enough space around the bed to easily open drawers. If you have basic power tools (a circular saw, drill, electric screwdriver) and experience with wood, you can do the work yourself on the weekend.

Below, see the diagrams and dimensions of sawing the details of the bed.

IN - 2 sheets of plywood 3/4 ”size 15 1/4 x 22” (39 x 56 cm), 1 pc. - 12 3/4 x 22 ”(32 x 56 cm)
IN - 1 sheet of plywood 3/4 ”size 22 x 55 3/4” (56 x 141.5 cm), 1 pc. - 15 1/4 x 57 1/4 ”(39 x 145 cm), 1 pc. 22 3/4 x 57 1/4 ”(58 x 145 cm)
A - 1 sheet of plywood 3/4 ”size 22 x 74 1/2” (56 x 189 cm), 1 sheet 15 1/4 x 76 ”(39 x 193 cm), 1 sheet 22 3/4 x 76” (58 x 193 cm)
A - 2 sheets of plywood 3/4 ”size 15 1/4 x 22” (39 x 56 cm), 1 pc. - 12 3/4 x 22 ”(32 x 56 cm)
C - 2 bars 2 × 4 long 57 ”(145 cm), 7 bars 2 × 4 long 27 1/2” (68.5 cm)
D - 1 rail 1 × 2 length 77 1/2 ”(197 cm), 1 pc. 12 ″ (30.5 cm), 1 board 1 × 3 length 77 1/2 ″ (197 cm), 2 parts 12 ″ (30.5 cm) long
D - 2 boards 1 × 3 length 80 ”(203 cm), 10 pcs. 12 ”(30.5 cm), 2 pcs. 80 ”(203 cm) long
E - 1 sheet of plywood 3/4 ”size 19 3/4 x 31 1/2” (50 x 80 cm), 2 pcs. 10 ”x19 3/4” (25.5 x 50 cm)
E - 1 PC. 11 3/4 "x 35" (30 x 89 cm), 2 pcs. 10 "x33" (25.5 x 84 cm)
F - 1 sheet of plywood 3/4 ”size 19 3/4 x 22 1/2” (50 x 57 cm), 2 pieces 10 ”x19 3/4” (25.5 x 50 cm)
F - 1 sheet of plywood 3/4 ″ 11 3/4 ″ x26 ”(30 x 66 cm), 2 pcs. 10 ″ x24 ”(25.5 x 61 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Platform storage bed drawing

Here are the drawings you can make bed platform with storage drawers do it yourself.

For assembly you will need plywood or MDF, glue and screws of different sizes from 80 to 30 mm.

The assembly sequence is shown in the diagrams in the gallery. The dimensions are in inches, just multiply these figures by 2.54, these will be the dimensions in centimeters. The instructions can be read on the website.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed for teenagers with shelves

Look at the drawings, how to make a bed for teens with storage shelves, which combines style and functionality. A very simple design that is not difficult to assemble with your own hands. Installed on a low platform, the bed will be an ideal resting place for a child. The main advantage is comfortable shelves at the head of the bed. For the shelf you need to saw such parts.
4 sheets of 3/4 "plywood, size 15 1/2" x 8 1/2 "(40 x 22 cm); 3 sheets 15 1/2" x 82 1/2 "(40 x 210 cm) and 2 sheets 15 1/2 "x 19 1/4" (40 x 49 cm)
1 1/4 "plywood sheet 84" x 19 1/4 "(213 x 49 cm)

Sawing for the bed:

• 2 2x4 bars 78 1/2 "long (200 cm)
• 4 2x4 bars, length 79 1/2 "(202 cm)
• 4 boards 1x3 long 5 1/2 "(14 cm) Conical ends
• 4 boards 1x4 long 5 1/2 "(14 cm) Conical ends
• 2 planks 1x2 length 73 "(185 cm)
• 2 slats 1x2 length 77 1/2 "(197 cm)
• 10 2x2 bars 5 1/2 "long (14 cm)
• 3 sheets of plywood 3/4 "size 28" x 80 "(71 x 203 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Wooden bed with storage drawers

Here are the drawings you can make simple bed with storage drawersto raise the mattress and provide extra space.

The design provides six large wide boxeswhich are perfect for children's toys, various things or even books. This bed has a depth of 30 cm. This drawing is also a basic plan for the modification of a double bed. In principle, the project is quite simple. Just imagine what you do small bookshelves. If you are working with MDF, use drywall screws and drill a guide hole to prevent the MDF from splitting. You will need to do box and two side compartments. Do not forget to nail the central partition.

For both backs: You can saw plywood into strips 38 cm wide to make it easier to work with. Then cut the plywood for the back and two sheets for the side cabins. Use nails and glue for fastening. Do the same for the side cabs. Trim the top first and the bottom of the long boards, as shown in the diagram. All outer edges should be flat. Then add a side trim while keeping the outer edges flush. Lay the slats on top as shown in the diagram. Do not use glue here. Read the full instructions on the website. In the gallery after assembly diagrams shown some examples of beds with storage drawers made according to these patterns.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Corner bed with shelves

Dimensional drawings and designs corner bed with shelves and storage drawers. First assemble the frame. Carefully align the edges without leaving any gaps between the components. Then attach 3/4 ″ plywood to the box frame. Next, you need to collect storage compartment components corner niche beds. Drill holes along the lower edges of the parts. Assembling the dividers is a simple process, you only need to fasten the 1 × 8 strips. Then fasten the top sheets of plywood. You can read more about the stages of assembling a bed with storage on the site.

A - 8 bars 2 × 2 29 "(73.5 cm) long, 4 pcs. 40 1/4" (102 cm), 2 pcs. 37 1/4 "(95 cm)
B - 1 sheet of plywood 1/4 ″ 40 1/2 ″ x 32 ″ (103 x 81 cm)
C - 1 sheet of plywood 3/4 ″ size 40 1/2 ″ x 40 1/2 ″ (103 x 103 cm)
D - 1 board 1 × 16 39 3/4 ″ long (101 cm), 1 pc. 40 1/2 ″ (103 cm)
E - 2 boards 1 × 8 length 39 3/4 ″ (101 cm)
F - 1 sheet of plywood 3/4 ″ size 40 1/2 ″ x 40 1/2 ″ (103 x 103 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Here is another example how to make a bed with shelves and lower drawers do it yourself. Firstly, you need to build the frame of the storage unit from 1 × 12 strips. Take the strips and attach them to the front surface using nails and glue. You can lock the pads togetherby drilling holes in pockets at both ends of the vertical components and screwing in 30 mm screws. Make sure the corners are square. From 1/4 ″ plywood, assemble the back and sand the edges. Make sure the edges are flat before hammering in nails. Do not leave gaps between parts. Assemble the casing at the top of the storage unit.

Materials

A - 2 boards 1 × 12 frame 40 (102 cm)
B - 5 boards 1 × 12 1 01/2 "long (27 cm)
C - 3 slats 1 × 2 40 1/2 ″ long (103 cm), 5 pieces 8 1/4 ″ long (21 cm)
D - 1 sheet of plywood 1/4 ″ size 12 ″ x 40 1/2 ″ (30.5 x 103 cm)

• 
• 
• 
• 
• 
• 
•  

Assembly instructions for the finished bed with drawers

Here is a drawing, how to assemble a wooden bed with drawers do it yourself.

Below are step-by-step photos of the DIY bed frame assembly.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Drawer couch

These drawings and diagrams show how to make light drawer with storage drawers! With this smart design, you get tons of extra storage space. Instruction how to make a couch do it yourself. You can read on the site, the link under the gallery. Some tips. Attach the handles to the front before attaching to the drawer so that you do not have to drill double thickness later. Check floor height - for example, a thick shaggy carpet can change the height of the drawers. Leave a small gap upstairs for crowded drawers or heavy weight on the bed frame.

The diagrams below show the assembly order, as well as a few examples. beds and couches made according to these drawings.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Storage bed with bedside tables

Here are some more drawings and diagrams, how to make a storage bed plus two bedside tables.

A description of the assembly process and about the necessary materials can be found on the website.

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Storage bed drawings

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•