Do-it-yourself double bed made of wood drawings

 

 Double bed with wooden headboard

This walkthrough shows and explains how to make a double bed with a wooden headboard do it yourself. The instruction that you can read on the site (link under the gallery) contains several points: planning and selection of materials, step by step instructions for the assembly of a wooden bed frame, the manufacture and assembly of the headboard and the selection of natural coatings for the wooden bed frame and headboard. You will also learn how to adapt drawings with calculations for making a bed of any size, for example king size or two single beds, with or without a headboard.

Below in the gallery you will find drawings, diagrams and step-by-step photos of the manufacturing process of a double bed with a headboard.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Double bed do-it-yourself drawings and photos

It may look like an ordinary double bed, but there is small touchesthat distinguish this design from other beds. For example, the lower bar connecting the two front legs gives it an elegant touch of modernism.

Double bed assembly shown in the drawings and step by step photos in the gallery.

There are a few points. Clips help to position the boards correctly. Attach the corner supports at the bottom of each 2x6 bar, first in the front corner and then in the opposite, as this will help align the bed frame. Clips help position the boards correctly. Attach the side supports so that the top of the board is 5 cm from the top. Wood glue will help fix the crossbar. Attach the center support post to the center support in the middle of the board using a pair of mounting screws. Then, the central support in the middle of the front and rear boards, so that the lower part of the support lines is attached to the lower side of the 2x6 bar. Attach the first support rail from above, close to the top of the crossbar. Then install each rail at a distance of 10 cm from the previous one.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself bed frame made of wood drawing

Step-by-step project how to make a king-size bed frame. Independent manufacture of furniture is not only a saving on the family budget, but also an opportunity to show your creativity. What you do with your own hands gives you the opportunity to choose design, size and finishthat fit your tastes. If you like a rustic style in the interior, you should like this project. Important tip, first buy a mattress, and then proceed to make a bed.

Rdimensions of parts according to the diagram on the right

A - 2 4 × 4 bars 52 inches (132 cm) long, 1 2 × 4 board 83 1/2 inches long (212 cm), 1 2 × 6 board 85 1/2 ”long (217 cm)
A - 14 boards 2 × 6 29 ”long (74 cm), 4 boards 1 × 4 76 1/2” long (194.5 cm)
B - 2 bars 4 × 4 25 ”(63.5 cm) long, 1 bar 2 × 4 83 1/2” (212 cm) long, 1 board 2 × 6 85 1/2 ”long (217 cm)
B - 14 boards 2 × 6 19 ”(48 cm) long, 4 boards 1 × 4 - 76 1/2” (194.5 cm)
C - 2 boards 1 × 10 length 80 1/2 ”(205 cm)
D - 2 bars 2 × 4 length 80 1/2 ”(205 cm), 1 bar 2 × 4 length 76 1/2” (194.5 cm)
E - 17 slats 1 × 4 length 76 1/2 ”(194.5 cm)

• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Another similar project with a simple design. Drawings are here to help you. make a double bed do it yourself in a rustic style. This frame is made mainly of 2x4 timber, so the design will be very strong and reliable.Always align components before tightening screws. Also desirable pre-drill holes under the screws, otherwise the tree can easily crack. To increase grip, use glue. Of course, only if you are not going to disassemble the structure in the near future.

A - 2 bars 2 × 4 33 inches (84 cm) long, 2 pieces 61 inches (155 cm) long, 11 pieces 17 1/2 inches (45 cm) long, 1 piece 70 inches (178 cm) long
B - 2 bars 2 × 4 - 33 inches (84 cm) long, 2 pieces 61 inches (155 cm) long, 11 pieces 6 inches (15 cm) long, 1 piece 70 inches (178 cm) long
C - 2 bars 2 × 4 with a length of 81 ”(206 cm) support strips
D - 3 bars 2 × 4 length 81 "(206 cm), 1 pc. Length 8" (20 cm)
E - 15 slats 1 × 4 61 inches (155 cm) long
14 2 × 4 bars 8 ′ (245 cm) long
15 boards 1 × 4 length 6 ′ (183 cm)
brackets for beds

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Queen bed

Project how to do do-it-yourself double bed. If you have a good drawing, then assembling a bed frame is a simple process. This design does not fundamentally differ from other examples, except in the dimensions of the parts. But still, to be sure read the instructions on the website, the link is under the gallery. The main advantage of home-made furniture is that you can always change the design of the bed to suit your needs and tastes.

Details are shown in the diagram, sawing in inches and centimeters is presented below.

A - 2 bars 4 × 4, length 52 inches (132 cm), 2 pcs. 26 inches long (65 cm)
B - 11 boards 1 × 6 29 inches (74 cm) long, 11 pieces - 20 inches (51 cm) long
C - 8 boards 1 × 6 60 1/2 ″ long (154 cm)
D - 2 bars 2 × 4 length 67 1/2 ″ (172 cm), 2 pcs. 69 1/2 ″ (177 cm) long
E - 2 boards 1 × 10 length 80 1/2 ″ (205 cm)
F - 2 bars 2 × 4 length 80 1/2 ″ (205 cm), 1 pc. 60 1/2 ″ (154 cm) long
G - 18 boards 1 × 4 60 inches (152 cm) long

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Double bed frame drawing

Presented here double bed drawings with step-by-step instructions so that you can do it yourself using only 2 × 4 bars. This is a full-sized bed frame that can be assembled in one day. The article provides detailed instructions, diagrams and drawings with dimensions. Make sure that the design matches the style of the rest of the furniture in the interior of your bedroom. The dimensions of the parts in the diagram are indicated by letters, see the translation in centimeters below.

• A - 2 bars 2 × 4 - 33 inches (84 cm) long, 2 pieces 54 1/2 inches (139 cm) long, 1 piece 63 1/2 inches (162 cm) long, 11 pieces - the length of the head of the bed
  
• B - 2 bars 2 × 4 21 "(53 cm) long, 2 pcs. 54 1/2" (139 cm), 1 pcs. 63 1/2 "(162 cm), 11 pieces 6" (15 cm) long
  
• C - 5 bars 2 × 4 length 75 1/2 ″ (192 cm)
  
• D - 17 2 × 4 bars, length 54 1/2 inches (139 cm)
  14 2 × 4 bars 8 ′ (245 cm) long
• 9 2 × 4 bars 10 ′ (305 cm) long
• stain
• brackets for beds

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Bed with decorative headboards

In the instructions, which includes step-by-step diagrams, where shown, how to make a beautiful double bed with decorative headboards. The order of this. Carefully draw an oval drawing on a 1x10 board, as shown in the diagram. Cut out the pattern by clearly identifying the centers before making any cuts on the boards (so you know where to align the ovals). After the ovals will be cut and polished, you will not be able to grind much after assembly, mark on the 1x4 and 1x8 boards places for placing an oval, as shown in the diagram. You can use a different type of leg. For additional support, you can add fifth foot to the center of the bedif necessary.

Headboard made the same way as the footboard, but with longer legs. Side panels are attached from the bottom of the footboard. Use 1/2 "pocket hole screws and wall brackets or long 80 mm screws on the outside. This bed is for use with spring mattress. Attach the studs flush to the bottom of the side rails with screws and glue.

Complete instructions with a list of materials and dimensions of sawing parts read on the site, link under the gallery.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Classic double bed

Since the instructions for making this bed basically coincide with the examples already presented above, here are simply presented drawings with dimensions, how to make king size headboard and footboard. Nothing complicated, beautifully placed boards, a little antique white paint, and you will have strong, simple, high-quality classic style bed.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Here is an example with step by step photos, how to make a double bed in a classic style do it yourself according to the drawings above.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Plus more 30 photos classic double beds

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Double bed do-it-yourself drawings and diagrams

After reading this walkthrough, you’ll learn how to make a wooden double bed with your own hands. The whole process is described in stages on the site. Some tips. The author recommends adding a flat metal bracket on the inside of the leg and side guide as additional support from wiggle. These sizes are designed for standard double bed mattress, if you want to fill the bedspread, you can add two or three centimeters on the sides. Although the footboard has enough space. The dimensions in the drawings are in inches, just multiply the figures by 2.54 to get the dimensions in centimeters.

Lumber sawing:

• 4 1x3 bars, length 77 1/2 "(197 cm), paneling panels
• 1 sheet of plywood 3/4 "size 77 1/2" x 32 "(197 x 80 cm) headboard panel
• 1 sheet of plywood 3/4 "size 77 1/2" x 16 "(197 x panel steps)
• 2 4x4 bars, length 53 1/2 "(136 cm), head of the head
• 2 4x4 bars 20 "(51 cm) long
• 2 2x4 bars 88 1/2 "long (225 cm) inner side walls
• 4 2x4 bars, length 74 1/2 "(189 cm), frame supports - add additional 2x4 supports for additional support
• 2 boards 1x12 83 "(211 cm) long side rails - 2x12s can also be used for additional support
• 2 boards 1x6 86 1/2 "(218 cm) long headers

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Similar double bed example, but the design is slightly different, since 4x4 bars and an easier way to connect the side rails to the head are not used. Bed sizes: 80 1/2 "x 91" x 57 "(205 x 231 x 145 cm). Sawing: side handrails and frame

• 2 boards 2 × 10 87 1/2 ″ long (side handrails)
• 2 - bar 2 × 4 length 88 1/2 ″ (side spikes)
• 8 2 × 4 bars 69 1/2 ″ long (more beams may be needed if your mattress is flimsy or decide not to add plywood on top)

Headboard

• 4 - 1 × 4 length 72 1/2 ″ (184 cm) panel trim
• 2 - 1 × 3 length 30 ″ (76 cm) panel ends
• 9 - 1 × 8 length 30 ″ (76 cm) main panels
• 2 - 2 × 4 length 34 1/2 ″ (88 cm) Inner foot for headboard
• 2 - 2 × 4 length 54 ″ (137 cm) External foot for headboard
• 1 - 2 × 4 length 78 1/2 ″ (200 cm) Top of legs and panel for headboard
• 1 - 2 × 6 length 80 1/2 ″ (205 cm) top of the head
• 2 - 2 × 4 length 10 ″ (25 cm) the lower part of the legs for the head

Footboard

• 4 - 1 × 4 length 72 1/2 ″ (184 cm) panel trim
• 2 - 1 × 3 length 15 ″ (38 cm) panel ends
• 9 - 1 × 8 length 15 ″ (38 cm) main boards on the panel
• 4 - 2 × 4 length 21 ″ (53 cm) feet
• 1 - 2 × 4 length 78 1/2 ″ (200 cm) upper legs and headboard
• 1 - 1 × 6 length 80 1/2 ″ (205 cm) top of the head

After the drawings 17 bed photosmade according to this instruction.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

King Bed

The drawings and diagrams shown show how to make a king size double bed do-it-yourself. Detailed instructions with a list of materials and sawing of parts with dimensions are on the site, link below. Assembly: you will need additional support for a large frame, so it’s recommended to add at least 4 central legs, as it shown on the picture. For heavier loads, you can add more legs. Please note that if the panels are less than 20 mm thick, you may need to use shorter hole for pockets or screws. You can also drill holes on the legs in the panel, if it is easier for you. After the schemes in the gallery are presented 15 examples of double bedsmade according to these drawings and diagrams.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Classic wooden farmhouse-style double beds 100 photos

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself double soft bed

Here is a great example where how to make a queen double soft bedwithout spending all your savings. For this you will need:

• 5.5 meters of beautiful fabric.
• 5.5 meters of inexpensive muslin.
• 5.5 meters of batting.
• One sheet of plywood 1/2 ″ thick. (For the head of the head.)
• One 3/4 inch thick plywood sheet. (For the platform.)
• 12 boards 1 x 4 for strips 245 cm long each
• 2 bars 2 x 2 ″ also 245 cm
• 1 thick beam 3 x 3 approximately 2 meters long for legs
• 4 slats 1 x 2 in size 245 cm long

The sequence of assembly of the bed is.

1. Using a jigsaw or hacksaw, cut the head out of 1/2 ″ plywood.
2. Assemble the frame, sides of 3/4 ″ plywood.
3. Headboard Upholstery. Start by laying it on the floor: fasten the muslin to cover the head of the bed, then three layers (more or less, if you like) of batting, and then a sheet of plywood that was cut out for the head. Then lay the headboard sheathed in muslin and cover it with a beautiful cloth.
4. Upholstery platform
5. Set your legs. You can simply buy ready-made legs at the hardware store if you want.
6. Attach the headboard to the platform

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Do-it-yourself soft bed with drawings

Take advantage of the drawings presented here and make your bedroom beautiful do-it-yourself soft double bed. If you have the necessary tools, it will take 8 hours at most. It’s only necessary to prepare all the materials, shopping list and sawing can be read on the site. And most importantly, here nothing to sew. From two pieces of plywood, cut two identical panels, as shown in the diagram. Tip: Use the first cut corner as a template for the other side. You will need a jigsaw for corner cuts. Use the template to mark the sides. Carefully cut with a jigsaw.

You will need to use both parts, so cut only along the line shown in the diagram. Make a headboard frame. You will need to pre-drill holes in the 4 × 4 bars. After assembling the frame, attach parts from plywood. Cut a piece of batting, burlap and a piece of cloth 5 meters long and about 50 cm wide. Fasten the burlap on the outside of the head of the head, then batting and then the cloth. Do not hurry, gently folding fabric around corners. Fasten the inside and back of the headboard. Trim excess tissue. Be sure to cover the bottom with plywood foot spacers. Just as you did the side handrails, wrap the bandwagon in burlap, batting and fabric, gently fastening from the inside. Screw the frame to the end plate. The bed can be moved to the desired room in two parts. For assembly, screw from the frame to the head, as shown above. The whole order is well shown in the diagrams in the gallery.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Canopy bed drawing

Create a unique interior, see how to make beautiful four-poster bed in the colonial style. In principle, it is not difficult to do. By design, this is an ordinary double bed, only with extended legs and crossbeams. First you need to trim the legs, as shown in the diagram. When making cuts, be sure to mark the long point and short point, as it will be difficult to distinguish a small angular section without marks on the board.

Then fasten the side parts and attach to the legs. After that install the central part. Then attach the skin or plywood to the back. Next, we build a footboard, similar to the headboard. It is better to assemble the parts separatelyso that you can easily move the bed to the room. Then assemble the parts and install the clamps that will support the mattress. Attach with screws to the inside of the bed guide. For additional support add center support. In short, the complete instructions can be read on the website. The assembly sequence is well shown in the diagrams in the gallery..

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

DIY bed on the platform

If you have low ceilings, or you just want to equip a berth in the attic, make a bed on the platform with your own handsis a good idea.

There are slight inconveniences, but some people like low beds, and then, the room looks more spacious. Below are the drawings.

Step by step instructions tool list and size cutting can be read on the site. The step-by-step photos show diagrams of the sequence of assembly of the bed, as well as several photos with examples of beds made according to this instruction.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Platform bed

According to these drawings, you can easily make a double bed on the platform with your own hands.

The construction is assembled from solid wood, according to the author, it took only 3 hours to make and paint!

Today such a style is in fashion, it is traditionally and at the same time modern. Want to make the same bed? Good! This bed was assembled using Kreg Jig. First, just collect the big box. But you have to make sure the box is square. Next, we make stands for mattresses. When King Size need center support. Then just crop the sides. If you plan to put this bed with the headboard against the wall, you can replace the 1x3 bars on the side of the headboard with 1x2. This will minimize the gap between the mattress and the wall behind the bed. Finally, attach the legs in accordance with the instructions of the legs manufacturer.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Another example how to make a platform bed with planks and solid wood frame with wooden legs. The bed is designed for full-size mattresses. Subtract 40 cm from the width to convert it into a lorry. To convert to king size, add 15 cm to the width and 12 cm to the length. Make a frame out2x6 boards, as shown in the diagram. Attach the spikes to the inside to support the slats. This average support is important for large beds. Attach so that the top is flush with the top of the spikes.

Add trim so that it is flush on the inside of the bed. Then add the pad on top and bottom, as shown in the diagram, with glue and screws. Attach the legs to the base of the bed. Now set the bars. The location of the slats and the quantity depends on your requirements for mattresses.. If you decide that the bed needs a little extra support in the center, the diagram shows the best way to strengthen the frame. The gallery below shows the frame assembly sequence. After the schemes, look again 30 bed examplesthe frames of which are made according to these drawings and diagrams.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Wooden frame for a double bed

Shown here how to assemble a frame for a double platform bed. It is a simple construction, but a bit heavy. You will need such lumber:

• (240 x 45 x 2480) x 4 - for the top and sides on each side
• (240 x 45 x 1360) x 6 - for the head and legs of the bed
• (195 x 45 x 610) x 2 - for the sides of the bed head

The sizes for each side, legs and head can be viewed on the website, as well as on drawings with dimensions in a gallery with step by step photos.

Sections gather in this order.

1. Glue and screw the top MDF plate to the front face.
2. Glue and screw the end plates of the MDF (if necessary).
3. Glue and screw the top part, then the front part to the MDF that you just collected
4. Glue and screw the back plate of the MDF
5. Glue and screw the base plate MDF

Note: Do not screw the screws too close to the corners as you will crack the MDF! And yet, do not take all measurements as 100% accurate. All assembly highlights see below for step by step photos.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•  

Double bed do-it-yourself drawings and diagrams

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
•